Home

How Do You Brew Coffee with a French Press?

To brew coffee with a French press, steep coarsely ground coffee in hot water for about four minutes, press the filter down gently and pour immediately. A reliable starting point is 30 grams of coffee to 500 ml of water, with small adjustments to suit your preferred strength.

What You Need for French Press Coffee

You need a French press, roasted coffee, drinking water, a kettle, a timer and a spoon. A kitchen scale makes measuring easier and gives more consistent results than counting spoonfuls. If you grind beans at home, a burr grinder usually produces more evenly sized particles than a blade grinder.

Check the usable capacity of your press before measuring the water. Leave enough space above the liquid to stir without spilling and fit the lid safely. Advertised cup counts can refer to much smaller servings than an ordinary coffee mug, so measuring the water yourself is more useful.

Use freshly ground coffee if possible, but ground coffee labelled for a French press is also suitable. Instant coffee does not need filtering, while very fine coffee intended for other brewing methods can make the plunger difficult to push and leave excessive sediment.

Choose the Grind Size and Coffee-to-Water Ratio

Start with a coarse, fairly even grind, with particles roughly resembling coarse sugar. A few fine particles are normal because the metal filter cannot remove everything. However, a large amount of powder can produce a muddy cup and increase resistance when you plunge.

A ratio of one gram of coffee to about 16 or 17 grams of water is a useful starting point. For a smaller brew, try 15 grams of coffee with 250 ml of water. Keep the same ratio when changing the batch size, provided the press can hold it comfortably.

If you do not have a scale, use roughly two level measuring tablespoons of ground coffee per 180 ml of water as an initial estimate. Spoon measurements vary with the grind and the coffee itself, so repeat the same measuring method each time. Adjust after tasting rather than assuming every spoonful weighs the same.

Strength and bitterness are not identical. Adding more coffee generally makes the drink stronger, while grind size, water temperature and steeping time affect how flavours are extracted. Change one factor at a time so you can tell which adjustment helped.

How to Brew Your Coffee Step by Step

For a first attempt, use water around 92°C to 96°C and a four-minute steep. Without a thermometer, let a freshly boiled kettle stand briefly before pouring; the cooling time varies with the kettle and the amount of water. Use a timer rather than estimating the steeping time.

  1. Warm the press. Rinse the jug with hot water, then empty it. This reduces the heat lost when you add the brewing water. Avoid pouring boiling water into damaged glass.
  2. Add the coffee. Put 30 grams of coarsely ground coffee into the empty press for a 500 ml brew. Place the press on a stable, heat-resistant surface.
  3. Pour and wet the grounds. Add the hot water steadily, making sure all the coffee gets wet. Give it a gentle stir with a wooden or silicone spoon, especially if the jug is glass.
  4. Fit the lid and steep. Keep the plunger raised, with the filter above the coffee. Let the coffee steep for about four minutes, counting from when you started adding water.
  5. Plunge slowly. Hold the lid steady and lower the filter with gentle, even pressure. Stop just above the compacted grounds rather than squeezing them.
  6. Pour straight away. Serve all the coffee, or transfer any extra into a separate insulated jug. Leaving it in contact with the grounds can change the flavour.

How to Adjust the Taste

If the coffee tastes thin but otherwise pleasant, increase the amount of coffee slightly while keeping the water quantity unchanged. If it tastes sharp and under-extracted, try a slightly finer grind or a little more steeping time. Make modest adjustments and note what you changed.

If the coffee tastes harsh or overly bitter, try a slightly coarser grind or a shorter steep. Darker roasts may also taste better with slightly cooler water. A distinctly burnt flavour can come from the roast itself, so brewing changes may not remove it.

Some sediment is normal with a French press because it uses a metal mesh rather than paper. Let the poured coffee settle briefly and leave the last small sip in the cup if the sediment bothers you. Avoid repeatedly pumping the plunger, which disturbs the grounds.

Clean the Press After Each Brew

Let the grounds cool before removing them, then put them in a suitable waste or compost container rather than washing them down the sink. Rinse the jug, plunger and filter, then wash with mild dishwashing liquid. Coffee oils left on the parts can make later brews taste stale.

Take the filter assembly apart regularly, following the manufacturer's instructions, to remove grounds trapped between the mesh and plates. Rinse away all soap and allow the parts to dry before reassembling. If plunging becomes difficult, check for a clogged filter or an overly fine grind instead of applying more force.